Imagine that you are riding on a Ferris wheel of radius 100 feet, and each rotation takes eight minutes. We can use angles in standard position to describe your location as you travel around the wheel. The figure at right shows the locations indicated by \(\theta = 0\degree,~ 90\degree,~ 180\degree,\) and \(270\degree\text{.}\) But degrees are not the only way to specify location on a circle.
We could use percent of one complete rotation and label the same locations by \(~p = 0,~ p = 25,~ p = 50,~\text{and}~ p = 75\text{.}\) Or we could use the time elapsed, so that for this example we would have \(~t = 0,~ t = 2,~t = 4,~\text{and}~ t = 6\) minutes.
Another useful method to describe your location uses the distance traveled, or arclength, along the circle. How far have you traveled around the Ferris wheel at each of the locations shown?
Before we consider that question, letβs agree on some vocabulary. An arc is a portion of a circle, and its length, quite naturally, is called arclength. An angle with vertex at the center of the circle is called a central angle, and a central angle whose sides meet the endpoints of an arc is said to subtend the arc. Or we may say that the angle spans the arc. If the arc represents a distance traveled, we sometimes refer to such an angle as the angle of displacement.
If we walk around the entire circumference of a circle, the distance we travel is \(2\pi\) times the length of the radius, or about 6.28 times the radius. If we walk only part of the way around the circle, then the distance we travel depends also on the angle of displacement.
For example, an angle of \(45\degree\) is \(\dfrac{1}{8}\) of a complete revolution, so the the length of the arc from point \(A\) to point \(B\text{,}\) called \(s\) in the figure at right, is \(\dfrac{1}{8}\) of the circumference. Thus
Similarly, the angle of displacement from point \(A\) to point \(C\) is \(\dfrac{3}{4}\) of a complete revolution, so the arclength \(s\) along the circle from \(A\) to \(C\text{,}\) shown at right, is
If you think about measuring arclength, you will see that the degree measure of the spanning angle is not as important as the fraction of one revolution it covers. This observation suggests a new unit of measurement for angles, one that is better suited to calculations involving arclength. Weβll make one change in our formula for arclength, from
\begin{equation*}
\textbf{Arclength}~ = ~ (\textbf{fraction of one revolution}) \cdot (2\pi r)
\end{equation*}
to
\begin{equation*}
\blert{\textbf{Arclength}~ =} ~ \blert{(\textbf{fraction of one revolution}\times 2\pi) \cdot r}
\end{equation*}
Weβll call the quantity in parentheses, (fraction of one revolution \(\times 2\pi\)), the radian measure of the angle that spans the arc.
For example, one complete revolution, or \(360\degree\text{,}\) is equal to \(2\pi\) radians, and one-quarter revolution, or \(90\degree\text{,}\) is equal to \(\dfrac{1}{4}(2\pi)\) or \(\dfrac{\pi}{2}\) radians. The figure below shows the radian measure of the quadrantal angles.
An angle of \(120\degree\) is \(\dfrac{1}{3}\) of a complete revolution, as we saw in the previous example. Thus, an angle of \(120\degree\) has a radian measure of \(\dfrac{1}{3}(2\pi)\text{,}\) or \(\dfrac{2\pi}{3}\text{.}\)
Radian measure does not have to be expressed in multiples of \(\pi\text{.}\) Remember that \(\pi \approx 3.14\text{,}\) so one complete revolution is about 6.28 radians, and one-quarter revolution is \(\dfrac{1}{4}(2\pi) = \dfrac{\pi}{2}\text{,}\) or about 1.57 radians. The figure below shows decimal approximations for the quadrantal angles.
Because they are "benchmarks" for comparing angles, you should be very familiar with both the exact values of these angles in radians and their approximations!
Look at the figure above. The second quadrant includes angles between \(\dfrac{\pi}{2}\) and \(\pi\text{,}\) or 1.57 and 3.14 radians, so 2 radians lies in the second quadrant. An angle of 5 radians is between 4.71 and 6.28, or between \(\dfrac{3\pi}{2}\) and \(2\pi\) radians, so it lies in the fourth quadrant.
It turns out that measuring angles in radians is useful for many applications besides calculating arclengths, so we need to start thinking in radians. To help that process, weβll first learn to convert between degrees and radians.
It is not difficult to convert the measure of an angle in degrees to its measure in radians, or vice versa. One complete revolution is equal to \(2\pi\) radians or to \(360\degree\text{,}\) so
Thus, the fraction \(\dfrac{180\degree}{\pi}\) (or its reciprocal \(\dfrac{\pi}{180 \degree}\)) gives us a conversion factor between degrees and radians:
Now let us return to our calculation of arclength, and weβll see the first instance in which measuring angles in radians is useful: To calculate an arclength we need only multiply the radius of the circle by the radian measure of the spanning angle, \(\theta\text{.}\) Look again at our formula for arclength:
\begin{equation*}
\blert{\textbf{Arclength}~ =} ~ \blert{(\textbf{fraction of one revolution}\times 2\pi) \cdot r}
\end{equation*}
The quantity in parentheses, fraction of one revolution \(\times 2\pi\text{,}\) is just the measure of the spanning angle in radians. Thus, if \(\theta\) is measured in radians, we have the following simple formula for arclength, \(s\text{.}\)
Thus, there is a special relationship between arclength and radians. An angle of 1 radian spans an arc on a circle equal to the radius of the circle, as shown at right. And the length of any arc is just the measure of its spanning angle in radians times the radius of the circle.
We can also use the formula in the form \(\theta = \dfrac{s}{r}\) to find an angle that spans a given arc. For example, an arclength equal to one radius determines a central angle of one radian, or about \(57.3\degree\text{.}\) In the next example, we compute a change in latitude on the Earthβs surface.
The radius of the Earth is about 3960 miles. If you travel 500 miles due north, how many degrees of latitude will you traverse? (Latitude is measured in degrees north or south of the equator.)
We think of the distance 500 miles as an arclength on the surface of the Earth, as shown at right. Substituting \(s = 500\) and \(r = 3960\) into the arclength formula gives
In the rest of this chapter we will see how to use the trigonometric functions sine, cosine, and tangent when the input variable is measured in radians instead of degrees, and why making that change greatly increases the utility of those functions. In Section 4.1 we connected the sine and cosine to the coordinates of points on a unit circle, a circle of radius 1. Here is an important observation that will inform our study:
Thus, on a unit circle, an arc of length 1 determines a central angle of 1 radian, or about \(57.3 \degree\text{.}\) And the measure of a (positive) angle in radians is equal to the length of the arc it spans. In other words, if we walk around the circle, each time we travel over an arclength of one radius, we turn through an angle of one radian.
The pond is a unit circle, so you have traversed an angle in radians equal to the arc length traveled, 4 miles. An angle of 4 radians is in the middle of the third quadrant relative to your starting point, more than halfway but less than three-quarters around the pond.
An ant walks around the rim of a circular birdbath of diameter 2 feet. How far has the ant walked when it has turned through an angle of \(210\degree\text{?}\)
From the list below, choose the best decimal approximation for each angle in radians in Problems 13β20. Do not use a calculator; use the fact that \(\pi\) is a little greater than 3.
The largest clock ever constructed was the Floral Clock in the garden of the 1904 Worldβs Fair in St. Louis. The hour hand was 50 feet long, the minute hand was 75 feet long, and the radius of the clockface was 112 feet.
If you started your walk at noon, how long would it take the minute hand to reach your position? How far did the tip of the minute hand move in its arc?
In 1851 Jean-Bernard Foucault demonstrated the rotation of the earth with a pendulum installed in the Pantheon in Paris. Foucaultβs pendulum consisted of a cannonball suspended on a 67 meter wire, and it swept out an arc of 8 meters on each swing. Through what angle did the pendulum swing? Give your answer in radians and then in degrees, rounded to the nearest hundredth.
A wheel with radius 40 centimeters is rolled a distance of 1000 centimeters on a flat surface. Through what angle has the wheel rotated? Give your answer in radians and then in degrees, rounded to one decimal place.
Clothes dryers draw 3.5 times as much power as washing machines, so newer machines have been engineered for greater efficiency. A vigorous spin cycle reduces the time needed for drying, and some front-loading models spin at a rate of 1500 rotations per minute.
The first large windmill used to generate electricity was built in Cleveland, Ohio in 1888. Its sails were 17 meters in diameter, and moved at 10 rotations per minute. How fast did the ends of the sails travel?
The largest windmill operating today has wings 54 meters in length. To be most efficient, the tips of the wings must travel at 50 meters per second. How fast must the wings rotate?
For Problems 47β52, find two points on the unit circle with the given coordinate.Sketch the approximate location of the points on the circle. (Hint: what is the equation for the unit circle?)
The angular velocity, \(\omega\text{,}\) of a rotating object is given in radians per unit time. Thus, an object that rotates through \(\theta\) radians in time \(t\) has angular velocity given by \(\omega = \dfrac{\theta}{t}\text{.}\) Find the angular velocity of the following objects.
Use the arclength formula to derive a formula relating linear velocity, \(v\text{,}\) and angular velocity, \(\omega\text{.}\) (See Problem 55 for the definition of angular velocity.) Start with the formula for linear velocity:
\begin{equation*}
\text{velocity} = \dfrac{\text{distance}}{\text{time}},~~~ \text{or} ~~~ v = \dfrac{s}{t}
\end{equation*}
and substitute the arclength formula for \(s\text{.}\)
Recall that to calculate a fraction of a revolution in degrees we divide the angle by \(360\degree\text{.}\) For example, \(90\degree\) is \(\dfrac{1}{4}\) of a revolution because \(\dfrac{90\degree}{360\degree} = \dfrac{1}{4}\text{.}\)
Use your expression to calculate what fraction of a revolution is represented by each of the following angles: \(~\theta = \dfrac{3\pi}{4}, ~~ \theta = \dfrac{5\pi}{3}, ~~ \theta = \dfrac{7\pi}{6}\text{.}\)